Skip to main content
EV charging

More EV Chargers, Same Power: Load Management vs Battery Storage

Power, not parking spaces, limits most EV charging projects. Here is how load management and battery storage let owners add chargers on an existing electrical service and control demand charges.

Wins Parking 6 min read
On this page
  1. Why power is the real limit
  2. What load management does
  3. Where load management fits best
  4. When battery storage makes sense
  5. A decision path for owners
  6. Common mistakes to avoid
  7. How Wins Parking handles this work
  8. Next step

Most parking lots can add more EV chargers without a new transformer. The tool is load management: software that shares a fixed amount of power across many chargers. Battery storage is the second tool. It helps most at DC fast-charging sites where short power spikes drive up demand charges.

This week the question got louder. On October 29, 2026, Blink Charging said it will rename itself Blink Energy and expand into energy management systems and battery storage. Days earlier, on October 26, LAZ Parking and EverCharge launched a multifamily charging offer built on dynamic load management. Both moves point at the same owner problem: power, not parking spaces, is the limit.

Why power is the real limit

A Level 2 charger is a large, steady load. The National Electrical Code treats it that way. NEC 625.42 states that EV charging loads "shall be considered to be continuous loads." Without controls, the service and feeder must be sized to the full rating of every charger.

That adds up fast. At a U.S. Department of Energy national lab garage, 108 Level 2 chargers rated at 6.7 kW each would draw about 720 kW if all ran at once. The existing transformers could not carry that. A transformer upgrade was too costly for the project budget.

Owners hit this wall in three places:

  • Service size. The panel and utility service may not have spare amps.
  • Transformer capacity. The utility may need to upgrade equipment before it will serve more load.
  • Demand charges. Many commercial rates bill for the highest power draw in the month, not just total energy.

What load management does

Load management caps the total power that a group of chargers can draw. Software then splits that power among the cars plugged in. When few cars charge, each gets full power. When many charge, each gets a share.

The code allows this. Under NEC 625.42, when an automatic load management system is installed, the maximum load on the service and feeder is the maximum load that the system permits. In plain terms, you size the wiring to the cap, not to the sum of every charger.

That lab garage is a working example. The lab capped total charger load at about 460 kW, down from the 720 kW uncapped peak. That kept the load within the existing transformers. Under the cap, each charger can drop to about 4.3 kW. The U.S. Department of Energy reports that this rarely happens, and chargers usually run at or near 6.7 kW.

Vendors make bigger claims for dense sites. EverCharge says its SmartPower system can allow "up to five times more charging ports per power source." Treat that as a manufacturer claim. Your ratio depends on your service, your drivers and how long cars stay parked.

Where load management fits best

Load management works best when cars park for hours. That covers most of the market:

  1. Apartments and condos. Residents park overnight. Most cars need far less energy than a full night at full power delivers.
  2. Workplaces. Employees park for a full shift.
  3. Hotels. Guests park overnight.
  4. Airport and park-and-ride lots. Cars sit for days.
  5. Fleet yards with overnight dwell. Vans and trucks return at night and leave in the morning.

It works less well where every driver needs a fast top-up at the same moment. A highway DC fast-charging stop is the clearest case.

When battery storage makes sense

A battery sits between the grid and the chargers. It charges slowly from the grid and discharges fast when a car plugs in. The grid sees a smaller, flatter load.

Batteries help most at DC fast-charging sites. Research from the National Renewable Energy Laboratory reviewed more than 7,500 commercial and industrial electricity rates. It found DC fast-charging electricity costs ranged from under $0.10 to over $2 per kWh. Low utilization was the main driver of high costs, especially on rates with demand charges. A site with few sessions can pay a full month of demand charges for a single short spike.

The Transportation Energy Institute studied the same problem. It named three ways to cut demand charges: rate design, co-located battery storage and managed charging. Its executive director called demand charges "a significant impediment to the deployment of EV chargers in the US."

A battery is a larger capital item than software. It also needs space, fire-code review and maintenance. For most Level 2 sites, load management alone solves the problem. For fast chargers on a constrained service or a demand-heavy rate, a battery can be worth pricing.

A decision path for owners

Use these five steps before you buy hardware:

  1. Pull 12 months of utility bills. Note the rate schedule, the peak kW each month and any demand charge line.
  2. Get the service capacity. An electrician can measure spare amps at the main panel. Ask the utility about transformer capacity.
  3. Map dwell time. List how long cars park by user group. Long dwell favors Level 2 with load management.
  4. Set a power budget. Decide the maximum kW you will give chargers. This becomes the load management cap.
  5. Price three options. Compare a service upgrade, load management on the existing service, and load management plus a battery. Include utility make-ready programs where your utility offers them.

Also confirm the local inspector accepts the load management system. Many manufacturers publish documents for the authority having jurisdiction. Ask for them early.

Common mistakes to avoid

  • Sizing for a peak that never happens. Twenty chargers rarely all run at full power at once. Paying for that peak in copper and transformers can waste capital.
  • Ignoring the rate schedule. A rate change can matter as much as hardware. Ask the utility if an EV-specific commercial rate exists.
  • Skipping future conduit. Running empty conduit while the lot is open costs less than trenching twice.
  • Picking a closed system. Ask whether chargers and software support open protocols, so you can change networks later.
  • Forgetting enforcement. A managed charger blocked by a gas car delivers nothing. Charging spaces need signs, rules and enforcement.

How Wins Parking handles this work

Wins Parking designs, builds and manages EV charging for parking owners. Our team starts with the power budget, not the charger count. We review your bills and service capacity, map dwell time and lay out charger locations with your parking plan.

Wins Design & Build, our construction division, handles trenching, conduit, pads, paving repair, striping and ADA access. Our management team runs the operating side: pricing, access rules, enforcement and reporting. We pair chargers with load management when the site calls for it, and we flag when a battery or service upgrade is the better call.

See our EV charging and parking management services, our guide to parking lot electrical upgrades for EV charging and our approach to multifamily EV charging. For past work, visit our case studies.

Sources for this article include the U.S. Department of Energy report on managed charging in a federal lab garage, NREL research on DC fast-charging electricity rates, EV Infrastructure News on Blink Energy and EV Infrastructure News on LAZ and EverCharge.

Next step

Call (970) 279-1744 or start at https://winsparking.com/contact. Bring 12 months of utility bills and a site plan, and we will tell you how many chargers your current service can support.

Frequently asked questions

What is EV charger load management?

It is software and hardware that caps the total power a group of chargers can draw and shares that power among the cars plugged in. When few cars charge, each gets full power. When many charge, each gets a share.

Does the electrical code allow load management for EV chargers?

Yes. NEC 625.42 says that when an automatic load management system is used, the maximum load on the service and feeder is the maximum load the system permits. Confirm the code edition your jurisdiction has adopted and the inspector's requirements.

Do I need battery storage for Level 2 chargers?

Usually not. Level 2 chargers serve cars that park for hours, so load management alone often keeps the site within its existing service. Batteries matter more at DC fast-charging sites with short, high power spikes.

What is a demand charge?

A demand charge is a utility fee based on the highest power draw during a billing period, measured in kW. One short spike can set the charge for the whole month, which can make low-use fast chargers expensive to run.

What should I gather before planning EV chargers?

Gather 12 months of utility bills, your rate schedule, the spare capacity at your main panel, how long each group of drivers parks, and a site plan. These set your power budget and charger count.

Sources

  1. energy.gov
  2. research-hub.nrel.gov
  3. evinfrastructurenews.com
  4. evinfrastructurenews.com
  5. sbcc.wa.gov
  6. d9prod.evcandi.com

How Wins Parking can help

Ready to Unlock Your Parking Revenue?

Request a proposal. Tell us about your property and we'll show you what's possible.

Your mobile information will not be sold or shared with third parties for promotional or marketing purposes.

Privacy Policy | Terms

Prefer to talk? Call or text 877-713-WINS (877) 713-9467 or (970) 279-1744